DIAGBOX V6.01 software download

How to download Software from obd2be.pdf

DIAGBOX V6.01 : http://s.dbank.com/e07qouuldn

Posted in Software | Comments Off on DIAGBOX V6.01 software download

Peugeot Planet 2000 Software download

How to download Software from obd2be.pdf

Peugeot Planet 2000 V24.21 : http://s.dbank.com/e048pwhifr

Posted in Operation Guide | Comments Off on Peugeot Planet 2000 Software download

Lexia 3 citroen Software download

How to download Software from obd2be.pdf

Lexia 3 V347.19 : http://s.dbank.com/e048pwhifr

Posted in Software | Comments Off on Lexia 3 citroen Software download

lexia 3 citroen operate.mp4

lexia 3 citroen operate

Posted in Review | Comments Off on lexia 3 citroen operate.mp4

lexia 3 installation and activate.mp4

lexia 3 installation and activate

Posted in Review | Comments Off on lexia 3 installation and activate.mp4

PEUGEOT 106,306,406, 605 fault codes

PEUGEOT 106 1996-97 fault codes

code Fault location
015Z The system relay.
018Z Rotors on the wheel speed sensor.
024Z Rear left wheel speed sensor.
025Z Front right wheel speed sensor.
031Z Rear right wheel speed sensor.
032Z Front left wheel speed sensor.
033Z The signal of the wheel speed sensors.
053Z The pump motor
055Z ECU
057Z The battery voltage is low.
058Z The battery voltage is high.
066Z In the ABS operation
067Z In the ABS operation.
068Z In the ABS operation.
069Z In the ABS operation.
087Z Fault with diagnosis output.
091Z The warning lamp.
095Z With the hydraulic connections.
096Z The connections to the wheel speed sensors are transposed.
097Z Is an external signal interference.
099Z No fault is found.

PEUGEOT 306(’97 onwards), 406(95-96), 605(96-97) fault codes

code Fault location
015Z The system relay.
016Z The BPP(Brake pedal position) switch.
018Z Rotors of the wheel speed sensors.
024Z Rear left wheel speed sensor.
025Z Front right wheel speed sensor.
031Z Rear right wheel speed sensor.
032Z Front left wheel speed sensor.
033Z The signal of the wheel speed sensors.
042Z The valves of the hydraulic modulator solenoid.
044Z The valves of the hydraulic modulator solenoid.
051Z The valves of the hydraulic modulator solenoid.
052Z The valves of the hydraulic modulator solenoid.
053Z The pump motor.
055Z The ECU.
057Z The battery voltage.
087Z Fault with diagnosis output.
091Z The warning lamp.
095Z With the hydraulic connections.
096Z The connections of the wheel speed sensors are transposed.
097Z Is an external signal interference.
099Z No fault is found.

Posted in OBD fault codes | Comments Off on PEUGEOT 106,306,406, 605 fault codes

lexia 3 peugeot planet 2000 Software activate.mp4

lexia 3 peugeot planet 2000 Software activate

Posted in Review | Comments Off on lexia 3 peugeot planet 2000 Software activate.mp4

lexia 3 Software activate guide

1. lexia 3 citroen peugeot diagnostic tool interface
lexia 3 citroen peugeot diagnostic tool User Manual

2. choose diagnostic

lexia 3 citroen peugeot diagnostic tool User Manual

3. choose test by function
lexia 3 citroen peugeot diagnostic tool User Manual

4. choose which function you want to diagnostic
lexia 3 citroen peugeot diagnostic tool User Manual
lexia 3 citroen peugeot diagnostic tool User Manual

5. choose ecu model
lexia 3 citroen peugeot diagnostic tool User Manual

lexia 3 citroen peugeot diagnostic tool User Manual

6. ecu connect ok
lexia 3 citroen peugeot diagnostic tool User Manual

lexia 3 citroen peugeot diagnostic tool User Manual

lexia 3 citroen peugeot diagnostic tool User Manual

Posted in Operation Guide | Comments Off on lexia 3 Software activate guide

Reboot Peugeot BSI

Reboot Peugeot BSI

Method for starting the BSI:
1.The very first step is to unplug the diagnostic tool from the vehicle.
2.Make sure all the gadgets are switched off, the driver’s window lowered down and open the bonnet.
3.Then close all the doors and take off the key from ignition.
4.After a 3 minute interval, unplug the vehicle’s battery terminals and wait for a further 15 seconds.
5.Attach back the battery terminals and give a 10 second pause making sure the doors are closed.
6.Turn the side lights on.
7.Now turn the engine on and inspect the system functioning.
8.Press and hold down the lock button on the key for 10 seconds.
9.Check the central locking system by unlocking and locking the door consecutively.
10.Turn the engine on again and finish inspecting the system.

Following any other procedure could cause malfunctioning of different units which depend on BSI.

Method for connecting the battery:
The following procedure is for reinstalling the battery connection unless told otherwise by Peugeot or Product service. Failure to follow this procedure may result in damage to the BSI’s embedded software during reconnection.
1.All the doors have to be closed with the ignition key turned off and the key taken out.
2.Now without opening the doors, replug the battery and wait for 10 seconds.
3.Turn on the headlights, turn on the engine and inspect the system’s functioning.

Method for unplugging the battery:
1.Before unplugging the battery, turn off all gadgets and lights, closing all the doors and unplugging any kind of diagnostic tool. The drivers side window has to be kept open for any kind of requirement.
2.Turn off the ignition and take out the key following which unplug the battery after an interval of 3 minutes.
3.The BSI needs to be taken to Sleep mode or Active Economy mode, during which nothing in the vehicle should be operating. Even the bonnet should not be opened that time as it can ‘wake up’ the BSI if the vehicle has got an alarm installed. For batteries under the bonnet, the bonnet should be opened and left up before allowing the BSI to go to Sleep Mode. During this 3 minute interval, use of any remote control central locking gadgets for other vehicles should be avoided in the vicinity of the concerned vehicle.

Posted in Operation Guide | Comments Off on Reboot Peugeot BSI

Peugeot FAQ

Peugeot FAQ

106 TU1ML (HDY&HDZ) MMG6
Fault:
Poor Idling
Cause:
Software deviation
Solution:
Replace control unit Eng TU1MLZ with Part No: 1929.5P & Eng TU1ML3 with Part No: 1929.5R.

106 TU1M&TU3M Bosch A2.
Fault:
Engine stalling, hesitates during the warm up phase after starting in an ambient temperature
below 20 degrees C.
Cause:
Unsuitable control unit programme
Solution:
TU1M replace control unit with Part No: 1929.F8&TU3M replace control unit with Part No: 1929.

106 TU1M&TU3M with Bosch A2.2
Fault:
Flashing of fault warning light, even though no fault code stored, engine cuts out at 3,000 rpm.
ECU’s marked TU1M eng 28SA2328 & TU3M eng 28SA2331.
Cause:
Overload of the processing calculation time.
Solution:
Replace control unit.

106 TU3JP Engine
Fault:
Engine sometimes stalls, unstable idle
Cause:
Idling is disturbed by the canister take-off, which is introduced on cylinder 4.
Solution:
Reposition the canister take-off point to the oil vapour re-circulation pipe.

106 TU3FJ2 Bosch MP3.1
Fault:
Engine hesitates at low speed accompanied by jerky acceleration, speed
fluctuates steadily and surges at idle. Slow return to idle.
Cause:
Premature fouling of injectors, incorrect spark plugs, unsuitable calibration of the control
unit and incorrect valve clearances.
Solution:
Check valve clearances is 0,20 mm Inlet & 0,40 Exhaust. Fit single electrode plugs
Champion RC7YCC (Part No: 5962.K1) Remove control unit protector, check the id
reference number which should be 26 SA 2922- if so replace with 1929.C4. Replace the
injectors (Part No 1984.84)

106-TU3JP TU5J4 TU1JP TU5JP -Magnetti Marelli 1AP
Fault:
Lack of power, flat spot when accelerating, may be accompanied by white smoke from
exhaust, engine runs on 2 cylinders and may store fault code for Lambda sensor.
All faults may occur intermittently.
Cause:
Intermittent fault in the ECU software.
Solution:
Download and reprogram control unit with latest version software.

106 TU5JP Bosch equipment
Fault:
Engine stalls after first starting.
Cause:
Unsuitable control unit calibration, disturbance of inlet air pressure information by air flow across
the idle solenoid.
Solution:
Replace throttle body with modified version with graduated butterfly Part No 1635.74. Measure
the diameter of the inlet air pressure information take-off tube, should be 5.1mm, if it isn’t, replace
the inlet manifold. Replace Eprom Part No 1929.2V ( this isn’t possible on control units with the part
numbers : 0261 200 052 suffix 26FM0026 & 0261 200 054 suffix 26FM0026). In these cases replace
the control unit with Part No: 1929.2T which corresponds to Bosch No: 0261 200 691 (106) or
0261 204 052 (306)

106 TU9.M Monojet MA 3.0 & MA 3.1
Fault:
Stalling on return to idle, hesitation during the warm up phase.
Cause:
Certain grades of fuel causes the throttle body to ice up.
Solution:
Replace the thermostatic valve (Part No 1424.7H)

106 TU9M Bosch MA 3.1 0261 204 625- 26FM0665
Fault:
Drop in engine speed/stalling during the warm up phase, lack of power when pulling away.
Cause:
Lack of reliability of control unit calibration.
Solution:
Download latest software update from CD rom 99.3

106TU3JP MM 1AP.81
Fault:
When hot engine speed periodically falls to 500 rpm
Cause:
Capacitor coupling between ignition coil control conductor & engine speed sensor conductor in the
wiring harness, due to inadequate suppression of the speed sensor harness from new.
Solution:
Replace control unit with modified suppression equipment Part No 1929.QT. If fault persists, replace
Sagem branded coils with Electricfil branded coils.

106 TU3JP MM 1AP
Fault:
Engine runs on 3 cylinders at idle and/or towards 2,000rpm with the engine hot.
Cause:
The coil within an injector has short circuited.
Solution:
Replace injector with modified satanised tip unit

106 TU9M Bosch MA 3.1
Fault:
Engine cut out and will not restart.
Cause:
Injector burned out
Solution:
Replace the injector with modified unit with resistance now 10 ohms instead of 6.7 ohms this runs at
a lower temperature.

106 TU3JP&TU5J4 MM 1AP.40 & 1AP.41 & 1AP.50
Fault:
Lack of power, flat spot when pulling away / accelerating. Could be accompanied by white smoke
from exhaust & engine running on 2 cylinders. Oxygen sensor fault code may be logged although
sometimes when hot engine runs correctly.
Cause:
Intermittent fault in the ECU software.
Solution:
Download and update software program

106 TU3JP MM 1AP.40
Fault:
When accelerating between 2,000 and 3,000 rpm engine is hesitating.
Cause:
Unsuitable calibration of the ECU
Solution:
Download new ECU calibration software, if fault persists replace the ECU.

106 TU5JP Automatic Gearbox Bosch MP 5.1 & MP 5.2
Fault:
When hot and during town driving engine is stalling.
Cause:
Deposits of oil and condensation forms inside the pipe that leads from the inlet manifold to the
MAP sensor
Solution:
Replace the MAP sensor pipe, cut it into 2 sections and insert buffer Part No 1957.46

106 TU1M Bosch MA 3.1 0261 204 622/788 0261 203 736
Fault:
With warm engine idle unstable.
Cause:
Incorrect distribution of the gas mixture within the inlet manifold
Solution:
Update ECU software, replace gearbox flexible mounting Part No 1843.95 Replace spark plugs
with Sagem RFN58LZ

106 TU9M MA 3.1
Fault:
Drivability faults following a cold start of 20 to 30 degrees, engine idle drops very low, vehicle
may stall
Cause:
The mixture is too rich
Solution:
Download a new control unit program. Check fuel pump identification strip, check fuel pressures.
Supply pressure should be 1.2 bar & return pressure should be 0.4 bar. Pump with orange
strip – if supply pressure is greater than 1.2 bar, fit a calibrated take-off Part No 1505.QR at the
fuel pump outlet. Pump with orange or yellow strip- if the return pressure is greater than 0.4 bar fit
a modified venturi to the pump Part No 1525.A9. If does not rectify pressure fault replace pump
Part No 1525.E1

106 TU1M+ engine
Fault:
When hot idle speed is too high, surging at idle.
Cause:
Incorrect assignment of the oil vapour re-circulation pipe and the servo vacuum take-off pipe on
the inlet manifold
Solution:
Correct position of pipes on inlet manifold. Oil breather pipe goes on engine side& servo pipe goes
on radiator side.

106 TU1M HDZ&HDY MM G6
Fault:
Hesitation, fast idle too high when cold, unstable idling and idle remains at 1200 rpm. Flat spot
when accelerating
Cause:
Calibration of the ECU
Solution:
Replace the ECU. TU1ML/Z Part No 1929.5P. TU1ML3 Part No 1929.5R

106 TU1M TU3JP and TU5JP
Fault:
When ancillaries are switched on engine stalls or idle speed dramatically decreases.
Cause:
The power consumed by the alternator at idle is to high.
Solution:
Fit an Alternator with progressive load Part No 5705.4L/4M
Note that on vehicles with crank pulley with only one groove replace with pulley with 5 grooves, replace belt.

106 TU3JP
Fault:
When engine is cold idle speed sticks at 2,000 rpm.
Cause:
Aluminium throttle housing faulty.
Solution:
Replace throttle housing with modified plastic version Part No 1635.K4

106 TU1.M Magnetti Marelli
Fault:
Engine running very rich, reasonable amounts of smoke, engine hesitates and stalls.
Cause:
MAP sensor pipe has become disconnected from the inlet manifold.
Solution:
De-grease the pipe and the tube connection to the manifold, Fit a clip to the pipe Part No 6981.99

106 TU1.M MMG6.
Fault:
Disturbance in engine operation, engine hesitation when driving.
Cause:
Crushing or cracking of the MAP sensor vacuum pipe, which is insufficiently resistant to hydrocarbons.
Solution:
Replace the pipe Part No 5953.06 & secure it to the inlet manifold using clip Part No 6981.99

106 TU3M TU3MC & TU9.M
Fault:
Stalling and hesitating of engine
Cause:
Deposits of oil breather in the mono-point injection unit and it’s electrical connectors
Solution:
Clean the mono-point housing and change the mono-point injection unit cover.

106 TU1M+ Bosch MA3.1
Fault:
Starting from cold and warm is poor. Hesitation during the warm up phase
Cause:
Intake air heater relay not sealed sufficiently & incorrectly positioned, causing water to enter &
corrosion of relay.
Solution:
Replacement of relay Part No 6555.45 increase size of hole to 4mm as near as possible to
the bottom edge located on the front pillar of the control unit support plate. Place the relay so
the connector is towards the right hand front wing.

106 TU3FJ2
Fault:
Poor drivability, lack of smooth acceleration and hesitation at light throttle settings
Cause:
Unsuitable control unit programming.
Solution:
Change control unit, ref 26 SA 1990. Replace injectors Part No 1984.84 Check valve
clearances: inlet 0.20 ,exhaust 0.40.

106 TU1.M Bosch A2.2
Fault:
Engine hesitative when accelerating cold, after starting from a temperature below 0 degrees C
Cause:
Unsuitable control unit programming
Solution:
Replace the 10k ohms resistor witch is fitted to the coolant temperature sensor. Fit control unit
ref 28 SA 2069 in place of the 28 SA 0000.

106 Magnetti Marelli 1AP
Fault:
Engine hesitation, lack of power & engine idle speed stick too high or too low.
Cause:
Water entering in to the throttle position sensor
Solution:
Check the operation of the throttle position sensor, if any doubt replace the sensor & fit a plastic
protector Part No 1635.N8 (Aluminium Throttle Body) Part No 1635.N9 (Plastic Throttle Body)

106 all Models
Fault:
Revs hold up when cold/jerky when at low speeds
Cause:
Manufacturer deviation in throttle body specifications
Solution:
Check if there is a white spot on the top of the plastic throttle housing. If there is not one replace
with Part No 1635Q0 (manual gearbox only). Check that the stepper motor part reference number
is: 19209L, which is on the body next to the connector- if not replace with correct version (manual
gearbox only)

106 TU9M Bosch MA 3.1
Fault:
When cold idle speed to slow, hesitation /flat spot when changing gear.
Cause:
Control unit calibration. No vehicle speed data
Solution:
Download new ECU control program. Take wire from the vehicle speed sensor add to the ECU.

306 TU5JP BOSCH MP 7.2
Fault:
Warning light is on, engine hesitation with fault memorised by the control unit of Injector control
short circuit to earth.
Cause:
Faulty Ignition coil (Sagem)
Solution:
Fit ignition coil block (Electrofil) Part No 5970.74 and 4 extension leads Part No 5963.19

306 TU3JP & TU5JP Engines.
Fault:
Faulty engine operation, starting not possible, hesitation, & timing fault
Cause:
Connection at the two- way connector to the engine speed sensor is faulty
Solution:
Re-make the engine speed sensor connection & lock it with a cable tie to the engine speed
sensor bracket.

306 XU10J4RS Engine
Fault:
Difficult to start when the engine is cold & when hot
Cause:
Mixture too rich during the start of the enrichment process
Solution:
Update control unit software

306 All Petrol Engines.
Fault:
Starting is difficult or impossible
Cause:
Plasticiser in fuel causing fouling of the spark plug electrodes – source Fuel filler tube
Solution:
Change the spark plugs & Intermediate fuel filler connection.

306 All engines
Fault:
The Tachometer, Fuel Guage and Speedometer are not working.
Cause:
Instrument panel has Faulty Microprocessor.
Solution:
Replace the instrument panel assembly

306 All Models
Fault:
Revs hold up when cold/jerky when at low speeds
Cause:
Manufacturer deviation in throttle body specifications
Solution:
Check if there is a white spot on the top of the plastic throttle housing. If there isn’t
one replace with Part No 1635Q0 (manual gearbox only). Check that the stepper motor
part reference number is: 19209L, which is on the body next to the connector- if not
replace with correct version (manual gearbox only)

405X5JP
Fault:
Hesitation on light throttle acceleration between 2,000 and 3,000 rpm;Engine surges at idle.
Hesitates when decelerating.
Cause:
Low rate of injector delivery.
Solution:
Replace injectors with new satinised versions part no 1984.71

405XU5JP SAGEM-LUCAS E.M
Fault:
After starting idle speed sticks at 3,000-4,000 rpm, all 10 fault codes stored (i.e. throttle position
sensor, MAP sensor).
Cause:
Control unit insufficiently screened against interference and goes into sleep mode after starting.
Solution:
Replace control unit with new modified version part no: 1929.V7 with a blue sticker.

405 XU5JP,XU7JP,XU10J2,XU10J4TE Fault:
Unstable idle; poor return from idle; diagnostic lamp on (fault code 21 stored).
Cause:
Throttle potentiometer quality fault.
Solution:
Fit a new revised throttle position sensor-part no 1920.0F

406 DW10DE & DW10ATED H.D.I. MODELS Fault:
Engine in emergency limp home mode& temporary faults stored in the fault memory.
Cause:
Wearing of the injection harness on a metal part of the gearbox, gearbox bolt or clutch-housing boss.
Solution:
Correct the position of the harness and fit bolt cover part no: 5733.74

406 ENGINE XUD11BTE
Fault:
When pulling away clutch judders.
Cause:
Slackening of the engine earth on the clutch housing next to the engine block.
Solution:
Tighten loose earth lead.

406 XUD11BTE Engine
Fault:
Starting difficult or impossible, once started no acceleration, although the fault may disappear after
restarting. Fault normally occurs when starting the engine from hot.
Cause:
Locking of the rotor of the injection pump following wear of the housing.
Solution:
Read the fault codes, the rotor 2 position sensor must be the only fault code stored. If the decod
rotor value is greater than 286 micro-seconds, remove & replace the injection pump.

406 Petrol models
Fault:
Battery warning light remains on for 3 seconds after turning the ignition off.
Cause:
Alternator regulator re-supplies voltage onto the alternator exciter terminal.
Solution:
Replace the alternator (Denso) with new unit Part No: 5705.1J with modified regulator.

Posted in FAQ | Comments Off on Peugeot FAQ